Datasheets

HP-77750-B

• HARD-BITE Point

The APF HARD-BITE Point with 7 integrally cast cutting teeth, breaks debris and boulders. The teeth cut into ledge rock for full bearing.

Download Datasheet

• Included:
• Points

HP 77600-B

• HARD-BITE Point

The APF HARD-BITE Point with 7 integrally cast cutting teeth, breaks debris and boulders. The teeth cut into ledge rock for full bearing.

Download Datasheet

• Included:
• Points

HP-7780-B

• HARD-BITE Point

The APF Hard-Bite point with 7 integrally cast cutting teeth, breaks debris and boulders. The teeth cut into ledge rock for full bearing.

Download Datasheet

• Included:
• Points

HP30000

• Champion Splicer

The Champion Splicer is a pair of U-shaped plates with flared ends that slip on easily and fit tightly into the two ends of the H-pile. Minimal prep work to the H-pile is required prior to attaching the Champion Splicer. Appropriate corner welds and partial penetration groove welds along the flanges of the splicer are required for attachment.

Download Datasheet

• Included:
• HP Splicer

PAR-T

• Super-Bite Point

The APF Super Bite point with continuous cutting teeth along the flanges and individual teeth along the web.

Download Datasheet

• Included:
• Points

APF-R-12

• H-Pile Injector Point

The APF Rock Injector point is a heavy duty point which provides dependable H-pile support in difficult ground conditions, especially sloping rock. Comparable to the “Oslo” point.

Download Datasheet

• Included:
• Injector Point

80500

• Rock Injector Point

The APF Rock Injector point is a heavy duty point which provides dependable H-pile support in difficult ground conditions. Comparable to the “Oslo” Point.

Download Datasheet

• Included:
• Injector Point

O-14000

• Outside Flange, Open End Cutting Shoe

The APF Outside flange cutting shoe helps to provide end protection to the pipe during installation. The pipe rests on the driving ledge rather than depending on welds in shear. The outside flange cutting shoe is used when drilling inside the pipe, past the tip or rock socketing the pipe is required.

Download Datasheet

• Included:
• Outside Flange
• Cutting Shoe

P-14006

• Inside Flange, Conical Points

Conical Points are the preferred end closure for pipe piles. The conical shape pushes the earth aside and preserves friction. The snub nose conical is an economical design which provides end protection in most soil conditions.

Download Datasheet

• Included:
• Conical Points
• Inside Flange

P-13006

• Inside Flange, Conical Points

Conical Points are the preferred end closure for pipe piles. The conical shape pushes the earth aside and preserves friction. This model is the heavy duty conical which generally is used for breaking through thick strata and difficult driving conditions. • Benefits: 60 degree Conical Points with heavy internal ribs aid in penetration in difficult soils. On boulders or uneven rock, the point helps to distribute the shock load around the periphery of the pipe rather than concentration it on a quadrant – as occurs with plate closure. 

Download Datasheet

• Included:
• Conical Points
• Inside Flange

VB9

• Inside Flange, Conical Points

Conical Points are the preferred end closure for pipe piles. The conical shape pushes the earth aside and preserves friction. This model is the heavy duty conical which generally is used for breaking through thick strata and difficult driving conditions.

Download Datasheet

• Included:
• Conical Points
• Inside Flange

S-20000 WF

• Weld Fit Pipe Pile Splicer

The weld fit splicer is recommended when tension and uplift values are required. Fillet welds both top and bottom are required for attachment.

Download Datasheet

• Included:
• Pipe Splicer

CP99

• Inside Flange, Conical Point

Conical Points are the preferred end closure for pipe piles. The conical shape pushes the earth aside and preserves friction. This model is the heavy duty conical which generally is used for breaking through thick strata and difficult driving conditions.

Download Datasheet

• Included:
• Conical Points
• Inside Flange

S-40000

• Backing Ring

The APF Split Backing Ring is fabricated from carbon steel. Backing rings are used when full penetration butt welds are specified. Chamfered pins set the proper gap for the initial root pass.

Download Datasheet

E22

• Sheet Pile Connectors

Engineered shape that provides a weld on connection for Larssen interlock sheet pile. The connector is welded onto the pile.

Download Datasheet

• Included:
• Larssen Interlock

SKLC-90

• Sheet Pile Connector

Engineered shape that provides junction connections for Larssen and most cold form interlock sheet pile. The connector is threaded into the sheet pile.

Download Datasheet

• Included:
• Larssen Interlock
• Cold-Form Interlock

SKAP

• Sheet Pile Connector

Engineered shape that provides a transition from a Ball & Socket to Larssen interlock sheet pile. The connector is threaded into the sheet pile.

Download Datasheet

• Included:
• Larssen Interlock
• Ball & Socket Interlock

SKP

• Sheet Pile Connector

Engineered shapes that provide a full range of corner and junction connections for ball and socket interlock sheet pile. The connector is threaded or welded onto the sheet pile. The SKP is available in several multi-functional designs; SKP90, SKP45, SKPT, SKPF, SKPM.

Download Datasheet

• Included:
• Ball & Socket Interlock

Larssen T

• Sheet Pile Connector

Cost effective and efficient way to transition the orientation of the sheet pile wall as compared to fabrication.

Download Datasheet

• Included:
• Larssen Interlock

T-9168

• Timber Point

Timber pile points are a pyramid shape for protecting the bottom of the timber. Use a size that fully covers the pointed end of the pile. The points are produced from 3/16" or 1/4" thick steel.

Download Datasheet

• Included:
• Point

T-8316

• Timber Boot

Timber piles can also benefit from protection by means of a flat boot. The trend to more powerful hammers and heavier design loading may mean that timber will be subjected to damaging blows as it hits obstructions or reaches end bearing. The boot covers the entire tip without pointing the pile and is available in different sizes. All that is required is slipping it on the pile and securing it with three nails.

Download Datasheet

• Included:
• Boot

C-19000

• Plastic Pile Caps

The plastic pile caps are injection molded in order to maintain a uniform thickness of 0.100". There a 4 pre-punched holes on the flanges for nailing. The cap can be used on pipe, timber, or concrete piles. Available in round or square; flat or cone shaped; black or white.

Download Datasheet

TC-7216

• Timber Uplift Connector

The galvanized uplift connector will provide tension capability between the timber piles and the concrete pile cap. Uplift anchors are ½" thick with 16" long threaded rod, washers & nuts. Available in 2 uplift anchor assemblies providing 6.6 kips uplift capacity or 4 uplift anchor assemblies providing 25.11 kips uplift capacity.

Download Datasheet

• Included:
• Connector

P-14006 20"

• Inside Flange, Conical Point

Conical Points are the preferred end closure for pipe piles. The conical shape pushes the earth aside and preserves friction. The snub nose conical is an economical design which provides end protection in most soil conditions.

Download Datasheet

• Included:
• Conical Points
• Inside Flange