Associated Pile

Datasheets

O-14000

  • Outside Flange, Open End Cutting Shoe

The APF Outside flange cutting shoe helps to provide end protection to the pipe during installation. The pipe rests on the driving ledge rather than depending on welds in shear. The outside flange cutting shoe is used when drilling inside the pipe, past the tip or rock socketing the pipe is required.

Download Datasheet

HP-77750-B

  • HARD-BITE Point

The APF HARD-BITE Point with 7 integrally cast cutting teeth, breaks debris and boulders. The teeth cut into ledge rock for full bearing.

Download Datasheet

HP 77600-B

  • HARD-BITE Point

The APF HARD-BITE Point with 7 integrally cast cutting teeth, breaks debris and boulders. The teeth cut into ledge rock for full bearing.

Download Datasheet

HP-7780-B

  • HARD-BITE Point

The APF Hard-Bite point with 7 integrally cast cutting teeth, breaks debris and boulders. The teeth cut into ledge rock for full bearing.

Download Datasheet

PAR-T

  • Super-Bite Point

The APF Super Bite point with continuous cutting teeth along the flanges and individual teeth along the web.

Download Datasheet

APF-R-12

  • H-Pile Injector Point

The APF Rock Injector point is a heavy duty point which provides dependable H-pile support in difficult ground conditions, especially sloping rock. Comparable to the “Oslo” point.

Download Datasheet

80500

  • Rock Injector Point

The APF Rock Injector point is a heavy duty point which provides dependable H-pile support in difficult ground conditions. Comparable to the “Oslo” Point.

Download Datasheet

HP30000

  • Champion Splicer

The Champion Splicer is a pair of U-shaped plates with flared ends that slip on easily and fit tightly into the two ends of the H-pile. Minimal prep work to the H-pile is required prior to attaching the Champion Splicer. Appropriate corner welds and partial penetration groove welds along the flanges of the splicer are required for attachment.

Download Datasheet

O-14001

  • Inside flange, Open End Cutting Shoe

The APF cutting shoe assists in providing end protection to the pipe during installation. An inside cutting shoe is needed when maximum friction surrounding the pile is desired. The pipe rests on the cutting shoe ledge rather than depending on welds in shear.

Download Datasheet

P-14006

  • Inside Flange, Conical Points

Conical Points are the preferred end closure for pipe piles. The conical shape pushes the earth aside and preserves friction. The snub nose conical is an economical design which provides end protection in most soil conditions.

Download Datasheet

P-13006

  • Inside Flange, Conical Points

Conical Points are the preferred end closure for pipe piles. The conical shape pushes the earth aside and preserves friction. This model is the heavy duty conical which generally is used for breaking through thick strata and difficult driving conditions. • Benefits: 60 degree Conical Points with heavy internal ribs aid in penetration in difficult soils. On boulders or uneven rock, the point helps to distribute the shock load around the periphery of the pipe rather than concentration it on a quadrant – as occurs with plate closure. 

Download Datasheet

VB9

  • Inside Flange, Conical Points

Conical Points are the preferred end closure for pipe piles. The conical shape pushes the earth aside and preserves friction. This model is the heavy duty conical which generally is used for breaking through thick strata and difficult driving conditions.

Download Datasheet

S-20000

  • Drive-On Pipe Pile Splicer

Of special interest for pipe piles is the Drive-On Splicer. Driving into the tapered splice compresses the pipe ends for a friction fit connection. No welding is required, speeding the job and minimizing the crew and equipment time.

Download Datasheet

S-20000 WF

  • Weld Fit Pipe Pile Splicer

The weld fit splicer is recommended when tension and uplift values are required. Fillet welds both top and bottom are required for attachment.

Download Datasheet

E22

  • Sheet Pile Connectors

Engineered shape that provides a weld on connection for Larssen interlock sheet pile. The connector is welded onto the pile.

Download Datasheet

SKLC-90

  • Sheet Pile Connector

Engineered shape that provides junction connections for Larssen and most cold form interlock sheet pile. The connector is threaded into the sheet pile.

Download Datasheet

CP99

  • Inside Flange, Conical Point

Conical Points are the preferred end closure for pipe piles. The conical shape pushes the earth aside and preserves friction. This model is the heavy duty conical which generally is used for breaking through thick strata and difficult driving conditions.

Download Datasheet

T-9168

  • Timber Point

Timber pile points are a pyramid shape for protecting the bottom of the timber. Use a size that fully covers the pointed end of the pile. The points are produced from 3/16" or 1/4" thick steel.

Download Datasheet

T-8316

  • Timber Boot

Timber piles can also benefit from protection by means of a flat boot. The trend to more powerful hammers and heavier design loading may mean that timber will be subjected to damaging blows as it hits obstructions or reaches end bearing. The boot covers the entire tip without pointing the pile and is available in different sizes. All that is required is slipping it on the pile and securing it with three nails.

Download Datasheet

C-19000

  • Plastic Pile Caps

The plastic pile caps are injection molded in order to maintain a uniform thickness of 0.100". There a 4 pre-punched holes on the flanges for nailing. The cap can be used on pipe, timber, or concrete piles. Available in round or square; flat or cone shaped; black or white.

Download Datasheet

SKP

  • Sheet Pile Connector

Engineered shapes that provide a full range of corner and junction connections for ball and socket interlock sheet pile. The connector is threaded or welded onto the sheet pile. The SKP is available in several multi-functional designs; SKP90, SKP45, SKPT, SKPF, SKPM.

Download Datasheet

Larssen T

  • Sheet Pile Connector

Engineered shape that provides a "T" connection for most Larssen interlock piles.

Download Datasheet

SKAP

  • Sheet Pile Connector

Engineered shape that provides a transition from a Ball & Socket to Larssen interlock sheet pile. The connector is threaded into the sheet pile.

Download Datasheet

© 2017 Associated Pile & Fitting. All rights reserved.
Associated Pile & Fitting • P.O. Box 1264, 45 Samworth Road, Clifton, NJ 07012-1264
Close